Download Motif XS AI Driver (Windows Vista/XP)
This driver requires MOTIF XS6, MOTIF XS7 and MOTIF-RACK XS to install mLAN16E2.
It enables you to connect a single n8, n12 or mLAN16E2 to a computer and transfer audio/MIDI signals via an IEEE1394 cable.
System Requirements For Windows XP Professional SP2 or later/XP Home Edition SP2 or later
Computer:
Intel Core/Pentium/Celeron family processor, with an S400 (400Mbps) IEEE1394 (FireWire) or i.Link terminal (*1).
Hard Disk:
Free disk space of 100 MB or more; high-speed hard disk
Recommended system requirements (*2)
CPU: Intel Core 2 Duo 1.66GHz (or higher)
Available Memory: 512 MB or more
Minimum system requirements (*2)
CPU: Intel Pentium 1.4 GHz or Intel Celeron
1.7 GHz (or higher)
Available Memory: 512 MB or more
System Requirements For Windows Vista (32bit)
Computer:
Intel Core/Pentium/Celeron family processor, with an S400 (400Mbps) IEEE1394 (FireWire) or i.Link terminal (*1).
Hard Disk:
Free disk space of 100 MB or more;high-speed hard disk
Recommended system requirements (*2)
CPU: Intel Core 2 Duo 1.8GHz (or higher)
Available Memory: 1 GB or more
Minimum system requirements (*2)
CPU: Intel Pentium 1.4 GHz or Intel Celeron 1.7 GHz (or higher)
Available Memory: 512 MB or more
*1 The computer must have an IEEE1394 (FireWire/i.LINK) connector.If there is no connector, install an IEEE1394 interface card (PCI or PC). For more details on system requirements and recommended PCI or PC cards, see the following page:http://www.yamahasynth.com/
*2 The system requirements listed here apply when playing the audio/MIDI data described below on a typical DAW. This may differ depending on the particular DAW you are using.
NOTE
When using a laptop or notebook computer, a built-in IEEE1394 terminal may not be available. If this is the case, install an appropriate PC interface card.
1394 Chip Set Compatible with MOTIF XS
- AGERE FW323-05
- AGERE FW323-06
- TI TSB12LV23 + PHY
- TI TSB12LV26 + TSB41AB03
- TI TSB43AB22/A
- TI TSB43AB23
- VIA VT6306
*ATTENTION
The manufacturer may alter the above mentioned Chip Set without notice. Depending on the change, there’s a possibility of it not working properly with MOTIF XS.
1394 Chip Set NOT Compatible with MOTIF XS
- NEC D72873GC
- NEC D72874GC
- NEC uPD72874
[Recommended System Requirements]
-Frequency/resolution: 44.1KHz/24-bit
-Audio playback tracks: 16
-Audio recording tracks: 1
-MIDI playback tracks: 18
-MIDI Remote Control / Automation Send -effects (plug-in): 3
-Insert effects (plug-in): 9
-Plug-in software synthesizer: 2
-Latency: about 6 msec
[Minimum system requirements]
-Frequency/resolution: 44.1KHz/24-bit
-Audio playback tracks: 15
-MIDI Remote Control / Automation Send -effects (plug-in): 3
-Insert effects (plug-in): 9
-Plug-in software synthesizer: none
-Latency: about 50 msec
Recommended system requirements (*1)
CPU: G5 2.3 GHz Dual or Core Duo 1.83 GHz or higher
Available Memory: 1 GB or more
Minimum system requirements (*1)
CPU: G4 1 GHz or higher
Available Memory: 512 MB or more
*1 The recommended/minimum system requirements listed here apply when playing the audio/MIDI data described below on a typical DAW. This may differ depending on the particular DAW you are using.
[Recommended system requirements]
-Frequency/resolution: 44.1 kHz/24 bit
- Audio playback tracks: 16
- Audio recording tracks: 1
- MIDI playback tracks: 18
- MIDI Remote Control/Automation
- Send effects (plug-in): 3
- Insert effects (plug-in): 9
- Plug-in synthesizer: 2
- Latency: about 5 msec
[Minimum system requirements]
- Frequency/resolution: 44.1 kHz/24 bit
- Audio playback tracks: 15
- MIDI Remote Control/Automation
- Send effects (plug-in): 3
- Insert effects (plug-in): 9
- Plug-in synthesizer: none
- Latency: about 50 msec