Old Motifator threads are available in the Archive.
dsetto
Total Posts: 433
Joined 01-24-2014 status: Enthusiast |
Have you used the Mutec FMC-07, 2GB Flash Board that Mutec claims is compatible with the Motif & MOXF? If so, how goes it? http://www.mutec-net.com/product_fmc-567.php?PHPSESSID=puu1npr5udv3vq4do70jp61e93 |
5pinDIN
![]() Total Posts: 11891
Joined 09-16-2010 status: Legend |
You might find these threads interesting:
|
dsetto
Total Posts: 433
Joined 01-24-2014 status: Enthusiast |
Yes, I remember those threads well. And surely, a refresher read will help. From what I recall, there weren’t all that many reports of actual users. I’d think that XF & MOXF users would be all over the Mutec 2GB Flash board, as it takes what’s very useful about the XF/MOXF and doubles it. I’ve brought it up again to see if there are more folks using it, and with positive results. (I.e., it works, and there’s no perceived latency.) Maybe I was mistaken to start a new thread. I did so to give the discussion a chance at a clean slate, |
5pinDIN
![]() Total Posts: 11891
Joined 09-16-2010 status: Legend |
It can “double it” if the individual samples are large enough. That limitation is covered in the linked threads.
Â
I’d think that by now if there were problems, they would have been brought up on the forums. However, I don’t see any problem with your having started this thread, and I encourage anyone who’s been using a Mutec 2 GB module to post their experiences with it. |
dsetto
Total Posts: 433
Joined 01-24-2014 status: Enthusiast |
yup, & yup |
lekanout
Total Posts: 82
Joined 07-19-2007 status: Experienced |
I’ve used it on a MOXF8 without any problems. |
dsetto
Total Posts: 433
Joined 01-24-2014 status: Enthusiast |
Thank you, lekanout. |
Captain Adrenalin
Total Posts: 342
Joined 02-17-2004 status: Enthusiast |
Hi, I’m using 2x2 GB of these boards in my XF. No issues so far. |
dsetto
Total Posts: 433
Joined 01-24-2014 status: Enthusiast |
And that’s the blessing I was looking for. 2x2. Oh yeah. |
dsetto
Total Posts: 433
Joined 01-24-2014 status: Enthusiast |
To get the XF signal-to-noise higher … Anybody else using the Mutec FMC-07 2GB Flash Board? If so, is it working out well? No perceptible latency, right? |
5pinDIN
![]() Total Posts: 11891
Joined 09-16-2010 status: Legend |
I haven’t as yet tried the Mutec 2GB board, although I’m tempted. It would be interesting to hear from others who are using them. However, I wouldn’t expect there to be any more latency than with the smaller Yamaha flash boards, since the Mutec boards use the same chips, just higher capacity. |
dsetto
Total Posts: 433
Joined 01-24-2014 status: Enthusiast |
Sounds good. It’s on my list. |
Michael Trigoboff
![]() Total Posts: 647
Joined 09-05-2011 status: Guru |
And mine too, unless I end up going over to the dark side and buy The Synth That Must Not Be Named. I just looked around, though, and I don’t see anywhere that’s selling the FMC-7. Sweetwater doesn’t have them, apparently, and neither does Amazon. Google Shopping seems not to have heard of them. Where do you buy these? |
cmayhle
Total Posts: 3116
Joined 10-05-2011 status: Guru |
Look Here, you are closer than you think! |
Michael Trigoboff
![]() Total Posts: 647
Joined 09-05-2011 status: Guru |
Thanks! My wife will be very amused. I have this same level of skill finding things around the house… :-) |
Michael Trigoboff
![]() Total Posts: 647
Joined 09-05-2011 status: Guru |
Is there a limit on the number of waveforms per flash board? Or is there just a limit for the entire XF? |