Old Motifator threads are available in the Archive.
luca_and_friends
Total Posts: 11
Joined 12-18-2014 status: Regular |
Hello,
The problem here is that I want to change the Parts, containing the sounds, without leaving my hands from the keyboard.
So, how can I solve the problem? I want to changes the part using the pedal in a order that I want, so: are there any program changes or sysex that I cannot see which whom I can work?
Thanks in advance,
|
luca_and_friends
Total Posts: 11
Joined 12-18-2014 status: Regular |
I’ve seen in Data List, page 104, that the program change is 63 -60 - 1/15..is it this? Anyone has tried that? THanks |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Each Song (or Pattern) Mixing can have up to 16 associated Mixing Voices. The Bank Select and Program Change message you asked about will change the Mixing Voice for the Part that has its MIDI Receive Channel matching the channel the message is sent on. By the way, for Program Change the range is 0-15 (not 1-15), which corresponds to Mixing Voices 1-16.
For example, if you send…
|
Vetalexy
Total Posts: 32
Joined 07-20-2015 status: Regular |
http://www.motifator.com/index.php/forum/viewthread/475646/ Sysex-command to switch the pattern sections:
F0 43 7E 00 ss 7F F7
It WORKS on the Yamaha MOXF6 in the Pattern mode. |
luca_and_friends
Total Posts: 11
Joined 12-18-2014 status: Regular |
Thanks for your help!
Sorry for these question, but I’m a little noobie with MIDI and this type of things.
Thanks in advance
|
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
You’re welcome.
Â
Yes, Bank Select requires Control Change messages. The MSB is sent with CC#00, the LSB with CC#32. Program Change will also have to be sent. For this to work, Voices in the Song should all be stored as Mixing Voices. http://www.motifator.com/index.php/support/view/bank_select_and_program_change If you are using a Song Mixing for live play, Pattern mode can also work for that. If you can use Pattern mode and send SysEx messages, see Vetalexy‘s post and the linked thread.
You haven’t mentioned how you would send messages to the MOX. You might want to look at devices from MIDI Solutions, such as
|
luca_and_friends
Total Posts: 11
Joined 12-18-2014 status: Regular |
Thanks again for your reply!
Now there’s a little problem:
How can I do for that? Basically I’m trying to mimic a button pressed in the 1-16 parts of the mox!
Thanks in advance,
|
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
I don’t know much about Max 7, so I can’t help with that. I do know that if you have each Part’s Voice STORED as a Mixing Voice, 63/60/PC will select the proper Mixing Voice. A Voice selection stored in a Mixing isn’t necessarily a Mixing Voice. So, let’s make sure that you’re creating Mixing Voices correctly. See Mixing Voice Edit on page 122 of the MOX Reference Manual. Did you select each Voice, press [F5]VCE ED, then press [STORE]?
Once you’re sure that the Voices have been STORED as Mixing Voices, things should work correctly. If you can’t get Max 7 to work then, you can try using MIDI-OX to send the controller messages as a test.
While I don’t have a MOX, using MIDI-OX I have verified that 63/60/PC properly selects Mixing Voices on both my XF and XS. You should also be aware that this method only selects the Mixing Voice for a Part - all the other Parameters of the Part will remain as they were. Therefore, it is not the same as selecting the Part from the MOX front panel. Again, if you can send SysEx and use Pattern mode, what Vetalexy posted is a good method. |
luca_and_friends
Total Posts: 11
Joined 12-18-2014 status: Regular |
Thanks again! Now it works! The thing is that is not like the same as selecting the part from the mox front panel!
What sysex I have to send to the mox for doing this?
Thanks again for your help and patience
|
luca_and_friends
Total Posts: 11
Joined 12-18-2014 status: Regular |
I’ve tried also with Vetalexy solution: “I was able to empirically to find a combination to change channels in song mode (mixing mode). A double line of command:
F0 43 10 7F 1C 00 0D 00 00 chan
But it doesn’t work.. as I’m workin with MOX6, the Yamaha Product ID should be “7F 14â€, but it doesn’t work the same.. I’m trying to send sysex with MIDI-OX, although it works with changing the Pattern in PATTERN MODE with the Vetalexy solution : “Sysex-command to switch the pattern sections:
F0 43 7E 00 ss 7F F7
....but, I want to change PARTs in SONG MODE as if I’m pressing the button in the front panel!
Thanks,
|
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
You have to be careful when converting SysEx from one model to another.
Try this in Song (or Pattern) mode…
For my XF and XS, that works with the proper model ID’s for those models. |
luca_and_friends
Total Posts: 11
Joined 12-18-2014 status: Regular |
That’s work nicely! Fantastic! Thanks for your help! Luca! |