Old Motifator threads are available in the Archive.
good-MO
Total Posts: 7
Joined 08-19-2012 status: Newcomer |
I want to Program change user number in MULTI mode by press number of keyboard controller or by FC controller(PCInc) but I cannot set it, while as I can set it in user VOICE mode . Now, when I select user MULTI mode and I press number of keyboard controller or FC controller(PCInc) for change user number there are not active. But, there are active in each part which I don’t want it.
How to set it ?
thank you. |
Bad_Mister
Total Posts: 36620
Joined 07-30-2002 status: Moderator |
The Rack XS has a specific Bank Select message to change the MULTI, while other Bank Select messages can be used to address each of the 16 Parts individually when sent on the specific MIDI channel of the PART. MSB/LSB = 63/68 address the entire Rack XS to change the MULTI… In must be sent on the DEVICE NUMBER Channel. The Bank Select message used in conjunction with the Program Change number will recall the MULTI
MULTI 001 is PROGRAM CHANGE 000
You don’t mention if your keyboard controller sends Bank Select MSB and LSB.
MSB = 063
|
good-MO
Total Posts: 7
Joined 08-19-2012 status: Newcomer |
Thank you for your advice.
THANK YOU. |
Bad_Mister
Total Posts: 36620
Joined 07-30-2002 status: Moderator |
You can manually enter the data on the TRACK. From the main SONG or PATTERN screen:
Press [EDIT] to view the Event List
Your MSB_LSB_PC will be 063-068-xxx
Below is an example taken from one of the SUPPORT Articles here on Motifator: ____________________
Bank Select – Program Change
Bank Select is a two byte Control Change (cc) message - a MSB (most significant byte) and a LSB (least significant byte) these two Control Change message each will have a value. This value identifies the bank. Messages will be between 000 and 127. The Bank Select information is followed by a Program Change number (also a number between 000 and 127)
The format is “xxx-yyy-zzzâ€
All normal GM sounds are in MSB = 000, LSB = 000
So a Program Change message in the Yamaha sequencer that is: Image Attachments
|
good-MO
Total Posts: 7
Joined 08-19-2012 status: Newcomer |
I set it but motif rack XS aren’t active in MULTI . in pic I want to change to USER MULTI 001 but not active. I must change by knob as before. Image Attachments
|
porgy
Total Posts: 2
Joined 01-12-2014 status: Newcomer |
Hello,
I have the same problem. I want to change the multi id by the program change of my master keyboard. This one is not able to send MSB.
|
good-MO
Total Posts: 7
Joined 08-19-2012 status: Newcomer |
Bad_Mister ..... Help us ... plz.
|
vleatt
Total Posts: 2
Joined 02-12-2011 status: Newcomer |
Hi, Bad_Mister You said, to change Multi program use
MSB = 063
I spent considerable time studying the manual before finding this post. Your answer works. Thanks! However, I went back to the manual and can’t find any mention of 63/68/xxx anywhere. Is it missing? Thanks. vleatt |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
It’s not missing, but perhaps you didn’t look in the correct manual.
See Bank Select on page 62 of the Motif-Rack XS Data List.
|
vleatt
Total Posts: 2
Joined 02-12-2011 status: Newcomer |
Thank you, 5pinDIN for a super-fast reply! I was looking in the correect manual - and on the correct page. It appears that this one line of information was left out of the manual. Everything down to 63 60 (mixing voice) is there, but the multi information is not. I had even thought of that possibility before I posted the question and downloaded a data list, but didn’t choose the Yamaha site, so I got another copy without the information. Thanks. I know I’m not going mad now and I’ll download from the link you gave me in case there is other missing information in my copy. I’m happy now! |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
You’re welcome. The link is to the “C” version of the Data List - apparently you were using an earlier version. I don’t know what other changes might have been made in the newer manual. Anyway, I’m happy that you’re happy. Â :-) |